[Sheflug] Trouble with BT Speedway Internal PCI card

["Kif HENDERSON" <nospam [at] xxxxxxxxxxxxxxxxxx>]

Hi,

I wonder whether anyone can help me.
I'm having problems getting my (e-smith SME) server to see my BT speedway
card internal PCI ISDN card (AVM Fritz - type=27 protocol=2)

There is no problem wi the card itself, if i throw it into a windows machine
it works fine.
I cant understand why the card isnt being seen. Is this an IRQ thing?
I notice that IRQ 10 is being assigned to the card.  This is also used by my
power management (bios). Is there a conflict here?
I've tried changing the IRQ used by power management in the bios but this
doesnt seem to have had any effect, and I believe the IRQ may be shared
anyway

Below is some information that i've gathered about my system:

dmesg gives the following (relevant) output

ISDN subsystem Rev: 1.114.6.7/1.94/1.140.6.3/1.85.6.2/1.21/1.5.6.2 loaded
HiSax: Linux Driver for passive ISDN cards
HiSax: Version 3.5 (module)
HiSax: Layer1 Revision 2.41.6.1
HiSax: Layer2 Revision 2.25
HiSax: TeiMgr Revision 2.17
HiSax: Layer3 Revision 2.17.6.1
HiSax: LinkLayer Revision 2.51
HiSax: Approval certification failed because of  unauthorized source code
changes <---------  not sure what  this is all  about ???
HiSax: Total 1 card defined
HiSax: Card 1 Protocol EDSS1 Id=HiSax (0)
HiSax: AVM PCI driver Rev. 1.22.6.3
FritzPCI: No PCI card found
HiSax: Card AVM Fritz PnP/PCI not installed !
ISDN-subsystem unloaded

lspci gives the following output:

00:06.0 Network controller: AVM Audiovisuelles MKTG & Computer System GmbH:
Unknown device 0e00 (rev 01)
 Subsystem: AVM Audiovisuelles MKTG & Computer System GmbH: Unknown device
0e00
 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
 Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
 Interrupt: pin A routed to IRQ 10
 Region 0: Memory at e8001000 (32-bit, non-prefetchable)
 Region 1: I/O ports at d400
 Capabilities: [40] Power Management version 2
  Flags: PMEClk- DSI- D1- D2+ AuxCurrent=55mA
PME(D0-,D1-,D2+,D3hot+,D3cold+)
  Status: D0 PME-Enable- DSel=0 DScale=0 PME-

cat /proc/pci gives the following output

Bus 0, device 6, function 0:
Network controller: AVM Unknown device (rev 1).
Vendor id=1244. Device id=e00.
Medium devsel. Fast back-to-back capable. IRQ 10.
Non-prefetchable 32 bit memory at 0xe8001000 [0xe8001000].
I/O at 0xd400 [0xd401].

cat /proc/interrupts doesnt list either the card or IRQ10

I'm a bit new to all this Linux stuff and i'm trying really hard to get a
decent system  up and running...
So far everything else has gone like a dream, I just need to get this
connection sorted and im off....

Can anyone help please?

Thanks a million...
Kif Henderson

___________________________________________________________________

Sheffield Linux User's Group -
http://www.sheflug.co.uk/mailfaq.html

  GNU the choice of a complete generation.